- The Complete Research Material is averagely 52 pages long and it is in Ms Word Format, it has 1-5 Chapters.
- Major Attributes are Abstract, All Chapters, Figures, Appendix, References.
- Study Level: BTech, BSc, BEng, BA, HND, ND or NCE.
- Full Access Fee: ₦6,000
Get the complete project »
ABSTRACT
This work is an attempt evolve a quicker and easier method of achieving Transportation. This will no doubt save considering human labour and time wasted involved in traditional manual method of transportation.
To achieve this, preliminary experiment was first carried out to determine the optimum speed of the motor vehicle. Various design alternative s for achieving the design solution were sythesized and a choice of an economic method which would satisfy the objective was made. Base on the principles guiding the performance of the motor vehicle, the dimensions and sizes of the various components were established.
Appropriate materials were subsequently selected and fabricated to require sizes. The motor vehicle was then assembled and tested.
After testing, it was found to perform efficiently this satisfying the objective for which it was designed.
CHAPTER ONE
INTRODUCTION
Automobile motor vehicle construction contributed a lot towards the economy of life in such a way that transportation is easier and quicker, with this we determined the distance man could travel, even without load.
This motor vehicle is basically designed for domestic, and industrial use. This motor vehicle designed to operate using internal construction engine, which is the most convenient source of power so far developed for driving road vehicles, which drives its power from the burning of fuel and air inside the engine cylinder.
The internal combustion engine (I.C.E) converts the chemical energy in fuel into heat energy and heat energy into mechanical energy. The heat energy is produced by a chemical reaction between the different elements of fuel and air in other ward burning. This burning of fuel and air takes place inside sealed to expand in all directions. This expansion of gases caused the only movable object (the piston) in the sealed chamber to move down, hence transferring the power produced in the cylinder to the crankshaft of the engine and then creating mechanical energy.
THE OBJECTIVE OF MOTOR VEHICLE CONTRUCTION
They are general objective of motor vehicle construction.
First, understand the historical and technical development of motor vehicle
Second objective is to understand the fundamental cycles of operation of he period and internal combustion engines.
Third objective is to know the constructional processes of motor vehicle.
Fourth objective is to understand the general principles of the transmission system of vehicle bodies. In order to achieve this we have to know the braking system and their operation principle and understanding the principles of steering mechanisms.
You either get what you want or your money back. T&C Apply
You can find more project topics easily, just search
-
SIMILAR MECHANICAL ENGINEERING FINAL YEAR PROJECT RESEARCH TOPICS
-
1. MODIFICATION OF A MOTORIZED MAIZE SHELLER
» TABLE OF CONTENTS Title page i Declaration ii Approval iii Dedication iv Acknowledgements v Table of Contents vi Abstract vii CHAPTER ONE 1.0 Backgrou...Continue Reading »Item Type & Format: Project Material - Ms Word | 33 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
2. THE DESIGN AND CONSTRUCTION OF A SPIN DRYER
» ABSTRACTThis work is aimed at designing and fabricating a spin dryer which can be used in drying spent grains after brewing. This will no doubt save c...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
3. THE USE OF WATERMELON SEED AS A COAGULANT IN INDUSTRIAL WASTE WATER TREATMENT (A CASE-STUDY OF NIGERIAN BREWERY, KADUNA)
» Abstract The use of water melon seed in purifying waste water from Nigerian brewery, Kudenden, Kaduna – Nigeria was carried out and its application ...Continue Reading »Item Type & Format: Project Material - Ms Word | 58 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
4. DESIGN AND CONSTRUCTION OF AN EXTERNAL CALIPER
» CONSTRUCTION OF AN EXTERNAL CALIPER Table of contents Title page Chapter one Introduction Background CHAPTER TWO: LITERATURE REVIEW CHAPTER THREE: MET...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
5. INVESTIGATION OF THE EFFECT OF MOULDING SAND (NATURAL & SYNTHETIC) ON CASTING OF FLANGE USING ALUMINIUM
» ABSTRACTThis study tend to investigate the effect of synthetic and natural moulding sand on casting of flange like component. In this study FUTA logo ...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
6. REGRESSION MODEL THAT COULD BE USED TO PREDICT THE REPAIR TIME IN HOURS OF A PEUGEOT CAR
» CHAPTER ONE Introduction 1.0 Introduction Time standards are realistic goals that must be accomplished by operators and technicians. They could be use...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
7. THE CONSTRUCTION OF A MOBILE REFRIGERATOR FRIDGE
» ABSTRACTThis write up focuses attention on a detailed report and account on the process of construction and formulation of plan for the actual and phy...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
8. CONSTRUCTION OF OFFICE TABLE
» ABSTRACT Furniture refers to movable objects intended to support various human activities such as sitting for chairs, Stools and Sofas, eating and rea...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
9. DESIGN AND CONSTRUCTION OF JOURNAL BEARING DEMONSTRATION RIG
» ABSTRACTThe journal bearing demonstration rig is an apparatus which is used to study how pressure would vary around the section of a journal bearing a...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
10. CONSTRUCTION OF A DOUBLE BUNK BED
» ABSTRACT This project is based on the construction of a double bunk bed which will serve a great place for resting and sleeping. It is done with avail...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT