- The Complete Research Material is averagely 52 pages long and it is in Ms Word Format, it has 1-5 Chapters.
- Major Attributes are Abstract, All Chapters, Figures, Appendix, References.
- Study Level: BTech, BSc, BEng, BA, HND, ND or NCE.
- Full Access Fee: ₦6,000
Get the complete project »
In this work, cutting fluid emulsion was developed from soya beans and the performance of the developed cutting fluid was evaluated by comparison with the conventional cutting fluid (control sample), using its ability to effectively perform as coolant during machining operation. The machining operation employed was the turning operation in which chips produced were collected and their surface finishes measured. The chips collected were evaluated for chip thickness ratio. Also, the temperature variations during cutting operation were measured using an infra- red gun thermometer. Temperature, surface finishing as well as chip formation rates using the developed cutting fluid under different cutting speed (rev/min), feed rate (mm/rev) and depth of cut (mm) was compared with that of the conventional cutting fluid. The average temperature of the work piece when developed cutting fluid was used as cutting fluid was 53.13 oC and that of the conventional cutting fluid was 54.7 oC. The result are very close, hence it shows better result in conducting heat away from cutting region. The developed cutting fluid gave an average high chip thickness of 0.446 mm while that of the conventional cutting fluid was found to be 0.316 mm. The high chip thickness of the developed cutting fluid is probably due to its better lubricating ability which allows easier and deep penetration of cutting tools. The average viscosity of the developed cutting fluid was found to be 31.1 poise at 29 oC, while the convectional cutting fluid was 47 poise at 29 oC. Low viscosity means high viscosity index, the developed cutting fluid has tendency to be fluid at higher temperature than the convectional fluid. In corrosion measurement, the developed cutting fluid shows no sign of corrosion; hence, the fluid has good ability to inhibit corrosion than the convectional cutting fluid.
You either get what you want or your money back. T&C Apply
You can find more project topics easily, just search
-
SIMILAR MECHANICAL ENGINEERING FINAL YEAR PROJECT RESEARCH TOPICS
-
1. STABILITY STUDIES OF SEMI –SUBMERSIBLE BODY IN LAMINAR AND TURBULENT FLOW ENVIRONMENT
» TABLE OF CONTENT Title Page CHAPTER ONE: INTRODUCTION 1.1 Background of Study 1 1.2 Statement of Problem 3 1.3 Objectives of Study 4 1.4 Scope and Lim...Continue Reading »Item Type & Format: Project Material - Ms Word | 71 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
2. DESIGN OF A MOTORIZED PINEAPPLE JUICE EXTRACTOR FROM LOCALLY AVAILABLE MATERIALS
» CHAPTER ONE INTRODUCTION 1.1 BACKGROUND Extraction is the process by which substances are removed from their original component or raw state. Hence, j...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
3. IMPLEMENTING TOTAL PRODUCTION MAINTENANCE IN NIGERIA MANUFACTURING COMPANY (DELTA STEEL COMPANY AS A CASE STUDY)
» ABSTRACT Companies around the world spend a lot of money on buying new equipment to increase production but a little is done to get hundred percent ou...Continue Reading »Item Type & Format: Project Material - Ms Word | 93 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
4. CONSTRUCTION OF OFFICE TABLE
» ABSTRACT Furniture refers to movable objects intended to support various human activities such as sitting for chairs, Stools and Sofas, eating and rea...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
5. APPRAISAL OF THE UTILIZATION OF INSTRUCTIONAL MATERIALS IN TEACHING AUTOMOBILE TECHNOLOGY IN TECHNICAL COLLEGES, KANO (A CASE STUDY OF SOME SELECTED S...
» TABLE OF CONTENTS Title page i Approval page ii Declaration iii Dedication iv Acknowledgment v Table of contents vi Abstract ix CHAPTER ONE: INTRODUCT...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
6. SKILL IMPROVEMENT NEEDS OF METAL WORK TECHNOLOGY TEACHERS IN TECHNICAL COLLEGES IN KADUNA STATE
» TABLE OF CONTENTS Title page i Approval page ii Declaration iii Acknowledgement iv Table of contents v Abstract vi CHAPTER ONE: INTRODUCTION Backgroun...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
7. DESIGN AND CONSTRUCT AN HANDHELD MAGNETIC METAL DETECTOR FOR THE PURPOSE OF DETECTING, LANDMINES, METAL TREASURES, ORE BY MINERS
» CHAPTER ONE INTRODUCTION 1.1 Background Information In the beginning metal detectors, couldn’t pick up everything deeper than one inch down. Thi...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
8. CONSTRUCT AN EFFECTIVE AND DURABLE BOOKSHELF SUITABLE FOR AN OFFICE
» ABSTRACT This study sought to establish youth Participation in Agricultural Activities in Jema’a Local Government of Kaduna State, Nigeria. The ...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
9. THE IMPACT OF PRODUCTION PLANNING AND CONTROL IN THE MANUFACTURING INDUSTRY
» ABSTRACT This research work, accessing the impact of production planning and control on productivity in the manufacturing industry. This study is focu...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
10. THE IMPACT OF JET APPARATUS
» ABSTRACTThis project is focused on experimental analysis of impact of water jet on vanes. This work intends to predict the output of a pelton wheel, a...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT