- The Complete Research Material is averagely 52 pages long and it is in Ms Word Format, it has 1-5 Chapters.
- Major Attributes are Abstract, All Chapters, Figures, Appendix, References.
- Study Level: BTech, BSc, BEng, BA, HND, ND or NCE.
- Full Access Fee: ₦6,000
Get the complete project »
ABSTRACT
The project is about fabrication of wheel barrow which is fabricated in mechanical Engineering workshop in institute of management and technology, Enugu.
The report comprise five chapters, chapter one is about the introduction (background of the study) of the wheel-barrow, chapter tow is about the literature review, chapter three is about the theory and analysis of problem, chapter four is about Assembling of the wheel barrow, chapter five is about conclusion, recommendation and references.
CHAPTER ONE
INTRODUCTION
1.1 Background of the Study
It is often said that man are born free back are always in Chain, in one way or the other, human beings are faced with a lot of problem. there was a time when it is difficult to carry a load from one place to anthem but as time goes one, solutions where prefer to this problem by providing a simple machine called wheelbarrow to help transport goods form one place to another.
A wheelbarrow is a small hand propelled vehicle usually with just one wheel, designed to be pushed and guided by a single person using two handles to the rear or by a sail to push the ancient wheelbarrow by wind. The machine has two hands where efforts are applied, it also has a portion where loads are loaded. The fulcrum takes change of it movement and so many other features. This machine is fabricated to relieve the difficulties and probably eliminate loss of man-power time, money and especially the need for technological break through self reliance.
1.2 AIM OBJECTIVES
The aim of fabricating this wheel barrow is as follows
1. To know how to fabricate a slandered wheel barrow.
2. To eradicate the problems faced by human’s in carrying goods form one place to another.
3. To lessen difficulties and probably eliminate lost of man-power
4. To identify how wheel barrow can be assistance in the society.
1.3 SCOPE AND LIMITATION
SCOPE
This study/work is designed to cover the construction or fabrication of a standard wheelbarrow.
LIMITATION
It is a difficult task to cover the fabrication of all simple machinery is Nigeria. The producer concentrated in the fabrication of wheelbarrow. During the fabrication, the producer also faced the following constantans.
a. Time: The time ell acted to this work is short compared to the production of the wheelbarrow.
b. Financial constraint: Financial is another problem faced by the producer during the constriction. There is no enough fund for the producer.
You either get what you want or your money back. T&C Apply
You can find more project topics easily, just search
-
SIMILAR MECHANICAL ENGINEERING FINAL YEAR PROJECT RESEARCH TOPICS
-
1. CONSTRUCTION OF A STEEL BOOK SHELF
» ABSTRACT The bookshelf had been successfully constructed. It was initiated so as to address the poor keeping of students’ files in various offic...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
2. DESIGN AND CONSTRUCTION OF OCEAN SURFACE AND SUBSURFACE CURRENT SIMULATOR
» CHAPTER 1 1.1 Introduction A ocean simulator is a physical basin or tank used to carry out hydrodynamic tests with ship models, for the purpose of des...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
3. CEMENT MANUFACTURING /PRODUCTION IN NIGERIA. A CASE STUDY OF EDO CEMENT FACTORY, UKPILLA, EDO STATE.
» ABSTRACT The project studied the manufacture of cement production in Nigeria using Ukpilla as a case study. It enables us to compare the differences b...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
4. MULTIDISCIPLINARY DESIGN OPTIMIZATION OF AN AIRCRAFT WING (AERODYNAMICS & STRUCTURAL)
» ABSTRACT The quest to operate at the cutting edge of technology is a worthwhile effort but requires intensive research and brilliant implementation of...Continue Reading »Item Type & Format: Project Material - Ms Word | 98 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
5. A PROJECT ON CONSTRUCTION OF PROPELLER AGITATOR
» ABSTRACT Propeller agitator is a specialized of various types of substances. It consists of three basic components which are the shaft, blade and the ...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
6. THE USE OF WATERMELON SEED AS A COAGULANT IN INDUSTRIAL WASTE WATER TREATMENT (A CASE-STUDY OF NIGERIAN BREWERY, KADUNA)
» Abstract The use of water melon seed in purifying waste water from Nigerian brewery, Kudenden, Kaduna – Nigeria was carried out and its application ...Continue Reading »Item Type & Format: Project Material - Ms Word | 58 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
7. INHIBITION EVALUATION OF CHEMICAL AND PLANT EXTRACTS ON THE CORROSION OF METALLIC ALLOYS IN ACIDIC ENVIRONMENT
» ABSTRACT Numerous failures and eventual losses in the chemical industry have been traced to corrosion processes. Failures resulting from the inability...Continue Reading »Item Type & Format: Project Material - Ms Word | 242 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
8. THE IMPACT OF PRODUCTION PLANNING AND CONTROL IN THE MANUFACTURING INDUSTRY
» ABSTRACT This research work, accessing the impact of production planning and control on productivity in the manufacturing industry. This study is focu...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
9. THE IMPACT OF PRODUCTION PLANNING AND CONTROL ON OPERATIONAL COST OF THE MANUFACTURING INDUSTRY (A Case Study of Nigeria Bottling Company Plc,)
» ABSTRACT This research work was designed to examine at the impact of production planning and control in manufacturing company as a primary function of...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
10. PRODUCTION OF A DEMONSTRATION PROTOTYPE FUEL SUPPLY SYSTEM IN OTHER TO ENHANCE THE LEARNING PROCESS OR TO GIVE A REAL PRACTICAL INSIGHT TO AUTOMOBILE ...
» In the past very little empirical research or project has been carried out to improve the effectiveness of student technical and practical know out. T...Continue Reading »Item Type & Format: Project Material - Ms Word | 34 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT